Lutz, Drum Pump, SL-HC 42, Extremely, Corrosive, Liquids

Lutz Drum Pump SL-HC 42 For Extremely Corrosive Liquids

Lutz, Drum, Container, Pumps, Non-Flammable LiquidsThe robust sealless pump tube is suitable for pumping nearly all kinds of liquids, whether extremely aggressive, clean or dirty, thin-bodied or slightly viscous non-flammable liquids out of drums and small or large containers. The pump tube is non-lubricated, thus preventing contamination of the liquids pumped.

Liquid examples:
Thin-bodied and slightly viscous mineral oils, Diesel fuel, fuel oil, cooling lubricants, crude oil, glycerine, fatty acids, linseed oil, etc.

Features:

  • Suitable for highly corrosive chemicals in non-explosive areas
  • Optional with electric or air driven motors
  • No grease fillings
  • Optimized drum drainage
  • Modular, service friendly design

Benefit

  • Sealless version cannot fail by dry running
  • Non-lubrictated, thus no contamination of the liquids pumped
  • All-purpose resistant PTFE shaft bearing
  • Two impeller geometries for a tailored pump characteristic
  • Easy maintenance without special tools
  • Sealing modules of mechanical sealed (MMS) resp. of sealless (MSL) pumps are replaceable

Sealing system:
Sealless construction (SL)

Type of impeller:
Axial-flow rotor (R) for high delivery rate.

Immersion length:
39" (1000 mm) and 47" (1200 mm)
(Special length on request)

Technical Data

Materials SL-HC
Housing: HC-22 (2.4602)
Seals: Viton® (FEP coated)
Mechanical seal: -
Bearings: Carbon
Drive shaft: Stainless steel (316)
Impeller: ETFE/Carbon
Type of impeller: Axial-flow (R)
Nominal diameter: 1,65"
42 mm
Temperature of medium: up to 248 °F
up to 120 °C
Hose connection: 1 1/4" male BSP
Length: 39" / 47"
1000 /1200 mm
 
Operating data Axial-flow (R)
Delivery rate:* up to 54.5 GPM
up to 205 l/min
Delivery head:* up to 40 ft.
up to 11 m wc
Viscosity:** up to 850 cps
up to 850 mPas

Motors

Motor B 36 / MI 4
Motor B 36-SC / MI 4 E

mi

Light, easily handled, high-performance motor, suitable for almost all types of thin-bodied, slightly viscous, aggressive and non-flammable liquids.

  • Light and convenient
  • Optionally with infinitely variable speed controller for a controlled flow rate
  • Internally ventilated
  • 110-120 V / 60Hz,
    640 W / 0.85 HP
  • Open drip proof in accordance with protection class IP 24, double insulated, 16´ (5 m) cord and plug

csa

Motor B 28

B28

Light, easily handled, high-performance motor, suitable for almost all types of thin-bodied, slightly viscous, aggressive and non-flammable liquids.

  • Light and convenient
  • Internally ventilated
  • 110-120 V / 60Hz,
    800 W / 1.07 HP
  • Open drip proof, double insulated, 16´ (5 m) cord and plug

Motor B 55-T-5 / MA II 5
Motor B 55-T-7 / MA II 7

B55-T

Light, easily handled, high-performance motor, suitable for almost all types of thin-bodied, slightly viscous, aggressive and non-flammable liquids. For very aggressive atmospheres an acid-proof motor is available.

  • Robust and powerful
  • Double wall housing protects inner parts from corrosion
  • Externally ventilated
  • 110-120 V / 60Hz,
    510 W / 0.68 HP (B 55-T-5)
    700 W / 0.93 HP (B 55-T-7)
  • TEFC splash-proof in accordance with protection class IP 54, double insulation with protective ground connection, 16´ (5 m) cord and plug

CSA

Motor MD-1 / MD-2

MD-1 / MD-2

Compact compressed air motor for handling neutral and aggressive liquids.

  • Overload-proof
  • Optionally with (MD-2) / without (MD-1) manual operation
  • Delivery flow is easy to control
  • 400 W / 0.54 HP at 87 PSI (6 bar) operating pressure, air consumption 32 CFM (0,88 Nm³/min.)

Motor 4/GT

4/GT

Light, easily handled compressed air motor for handling neutral and aggressive liquids.

  • Overload-proof
  • Delivery flow is easy to control
  • 220 W / 0.3 HP at 87 PSI (6 bar) operating pressure, air consumption 14 CFM (0,38 Nm³/min.)

Motor MA II 3-12V

B55-T

Light, easily handled, high-performance motor, suitable for almost all types of thin-bodied, slightly viscous, aggressive and non-flammable liquids.

  • Robust and powerfull
  • Double wall housing protects inner parts from corrosion
  • Externally ventilated
  • 12 V DC,
    260 W / 0.35 HP
  • TEFC splash-proof in accordance with protection class IP 54, double insulation with protective ground connection, 10´ (3 m) cord with alligator clips

Motor B 4/GT

B 4/GT

Reliable and persistant three-phase gear motor suitable for pumping thin-bodied to slightly viscous liquids in plant construction and stationary use.

  • Robust and durable
  • Especially smooth and quiet operation
  • Long maintenance intervals
  • 230/440 V / 60Hz 
    750 W / 1.0 HP
  • TEFC splash-proof in accordance with protection class IP 54

Catalogue Pages Downloads
Catalogue pages Pump SL-HC 42

Performance Curves Downloads
Performance Curve Pump MS-HC 38 with Motor 4/GT (pdf, 0.06 MB)
Performance Curve Pump MS-HC 38 with Motor B28 (pdf, 0.06 MB)
Performance Curve Pump MS-HC 38 with Motor B36/MI 4 (pdf, 0.06 MB)
Performance Curve Pump MS-HC 38 with Motor B55-T-5/MA II 5 (pdf, 0.06 MB)
Performance Curve Pump MS-HC 38 with Motor MA II 3 - 12V (pdf, 0.06 MB)
Performance Curve Pump MS-HC 38 with Motor MD-1/MD-2 (pdf, 0.06 MB)