The PD6060 is a member of the ProVu series of 1/8 DIN digital
panel meters that accepts two inputs of either a process current
(4-20 mA) or process voltage (0-5V, 1-5V, etc.) signal. It displays
these signals on a dual line, 6-digit display that is available
with an optional Sunbright® sunlight readable LEDs. The
meter can be customized such that these two inputs are displayed
in a variety of ways, including both at the same time with tags
or the result of math functions performed on one or both of
the inputs. Like all ProVu meters, the PD6060 includes UL /
C-UL listing and CE marking, a NEMA 4X front, and AC or DC power
options. The PD6060 can also be equipped with up to four internal
relays, a 4-20 mA analog output, and Modbus® serial communications.
The PD6060 includes a 24 V DC power supply to drive the transmitters.
ProVu meters can be programmed via the front panel pushbuttons
or free MeterView® Pro software.
Display: Upper display: 0.60" (15 mm) high. Lower display:
0.46" (12 mm) high. Both are 6 digits (-99999 to 999999),
Display Intensity: Eight user selectable intensity levels
Display Update Rate: 5/second (200 ms)
Overrange: Display flashes 999999
Underrange: Display flashes -99999
Display Assignment: The Upper and Lower displays may be
assigned to process values for Channels A (Ch-A), B (Ch-B),
or C (Ch-C), toggle between (Ch-A & Ch-B, Ch-A & Ch-C,
Ch-B & Ch-C, and Ch-A, Ch-B, & Ch-C), toggle between
Channel & units, show channel gross value (no tare) or
toggle net (tare) and gross values, show relay set points,
max & min values, or
Modbus input. The second display may also be set to show
engineering units or be off, with no display.
Front Panel: NEMA 4X, IP65
Programming Methods: Four front panel buttons, digital inputs,
PC and MeterView Pro software, Modbus registers
F4 Digital Input Contacts: 3.3 VDC on contact. Connect normally
open contacts across F4 to COM.
F4 Digital Input Logic Levels: Logic High: 3 to 5 VDC
Noise filter: Programmable from 2 to 199 (0 will disable
Filter Bypass: Programmable from 0.1 to 99.9% of calibrated
Recalibration: All ranges are calibrated at the factory.
Recalibration is recommended at least every 12 months.
Max/Min Display: Max (Peak) / min (Valley) readings reached
by the process are stored until reset by the user or until
power to the meter is cycled.
Password: Three programmable passwords restrict modification
of programmed settings.
Non-Volatile Memory: All programmed settings are stored
in non-volatile memory for a minimum of ten years if power
Power Options: 85-265 VAC 50/60 Hz, 90-265 VDC, 20 W max,
or optional model with 12-24 VDC ±10%, 15 W max.
Fuse: Required external fuse: UL Recognized, 5 A max, slow
blow; up to 6 meters may share one 5 A fuse.
Isolated Transmitter Power Supply: Terminals P+ & P-:
24 VDC ± 10%. Internally selectable jumper for 24,
10, or 5 VDC supply.
85-265 VAC models rated @ 200 mA max, 12-24 VDC powered
models rated @ 100 mA max, @ 50 mA max for 5 or 10 VDC supply.
Normal Mode Rejection: Greater than 60 dB at 50/60 Hz
Isolation: 4 kV input/output-to-power line. 500 V input-to-output
or output-to-P+ supply.
Overvoltage Category: Installation Overvoltage Category
II: Local level with smaller transient overvoltages than Installation
Overvoltage Category III.
Environmental: Operating temperature range: -40 to 65°C
Storage temperature range: -40 to 85°C
Relative humidity: 0 to 90% non-condensing
Connections: Removable screw terminal blocks accept 12 to
22 AWG wire, RJ45 for external relays, digital I/O, and serial
Enclosure: 1/8 DIN, high impact plastic, UL 94V-0, color:
Mounting: 1/8 DIN panel cutout required: 3.622" x 1.772"
(92 mm x 45 mm). Two panel mounting bracket assemblies are
Channels: Channel A, Channel B, Channel C (Math channel)
Programmable Constants: Constant P (Adder): -99999 to 999999,
default: 0.000; Constant F (Factor): 0.00001 to 999999, default:
Math Functions: Addition, difference, absolute difference,
average, multiplication, division, max of A or B, min of A
or B, draw, weighted average, ratio, concentration. See instruction
manual for details.
Sequence of Operations for Input Programing:
1.Select Input for A and B
2.Set up the engineering units for A, B, and C
3.Set up decimal point for A, B, and C
4.Scale A & B
5.Set up the displays for A, B, or C
6.Select the transfer function for A & B (e.g. Linear)
7.Select Math function for Channel C
8.Program constants for Factor (F) and Adder (P).
9.Program cutoff values for A and B
Accuracy: ±0.03% of calibrated span ±1 count,
square root & programmable exponent accuracy range: 10-100%
of calibrated span
Temperature Drift: 0.005% of calibrated span/°C max
from 0 to 65°C ambient, 0.01% of calibrated span/°C
max from -40 to 0°C ambient
Signal Input Conditioning: Linear, square root, programmable
exponent, or round horizontal tank volume calculation.
Multi-Point Linearization: 2 to 32 points for channel A
Decimal Point: Up to five decimal places or none: d.ddddd,
dd.dddd, ddd.ddd, dddd.dd, ddddd.d, or dddddd.
Calibration Range: 4-20 mA: minimum span input 1 & input
2: 0.15 mA. ±10 V: minimum span input 1 & 2: 0.10
V. An Error message will appear if input 1 and input 2 signals
are too close together.
Input Impedance: Voltage ranges: greater than 500 kO. Current
ranges: 50 - 100 O (depending on resettable fuse impedance).
Input Overload: Current input protected by resettable fuse,
30 VDC max. Fuse resets automatically after fault is removed.
HART Transparency: Analog input will not interfere with
existing HART communications on the wired 4-20 mA signal
Rating: 2 or 4 SPDT (Form C) internal and/or 4 SPST (Form
A) external; rated 3 A @ 30 VDC and 125/250 VAC resistive
load; 1/14 HP ( 50 W) @ 125/250 VAC for inductive loads.
Noise Suppression: Noise suppression is recommended for
each relay contact switching inductive loads.
Deadband: 0-100% of span, user programmable
High or Low Alarm: User may program any alarm for high or
low trip point. Unused alarm LEDs and relays may be disabled
Relay Operation: automatic (non-latching), latching (requires
manual acknowledge), sampling (based on time), pump alternation
control (2 to 8 relays), Off (disable unused relays and enable
interlock feature, manual on/off control mode).
Relay Reset: User selectable via front panel buttons or
1.Automatic reset only (non-latching), when input passes the
2.Automatic + manual reset at any time (non-latching).
3.Manual reset only, at any time (latching).
4.Manual reset only after alarm condition has cleared (latching).
Note: Front panel button or digital input may be assigned
to acknowledge relays programmed for manual reset.
Time Delay: 0 to 999.9 seconds, on & off relay time
delays. Programmable and independent for each relay.
Fail-Safe Operation: Programmable and independent for each
relay. Note: Relay coil is energized in non-alarm condition.
In case of power failure, relay will go to alarm state.
Auto Initialization: When power is applied to the meter,
relays will reflect the state of the input to the meter.
Protocol: Modbus® RTU
Meter Address/Slave ID: 1 - 247
Baud Rate: 300 - 19,200 bps
Transmit Time Delay: Programmable between 0 and 199 ms
Data: 8 bit (1 start bit, 1 or 2 stop bits)
Parity: Even, odd, or none with 1 or 2 stop bits
Byte-to-Byte Timeout: 0.01 - 2.54 seconds
Turn Around Delay: Less than 2 ms (fixed)
Note: Refer to the ProVu Modbus Register Tables located at
www.predig.com for details.
Isolated 4-20 mA
Output Source: Process channel A, B, or C, max or min for
channel A, B, or highest or lowest max or min of A and B,
set points 1-8, Modbus input, or manual control mode
Scaling Range: 1.000 to 23.000 mA for any display range
Calibration: Factory calibrated: 4.000 to 20.000 = 4-20
Analog Output Programming: 23.000 mA maximum for all parameters:
Overrange, underrange, max, min, and break
Accuracy: ±0.1% of span ±0.004 mA
Temperature Drift: 0.4 µA/°C max from 0 to 65°C
ambient, 0.8 µ/°C max from -40 to 0°C ambient
Note: Analog output drift is separate from input drift.
Isolated Transmitter Power Supply: Terminals I+ & R:
24 VDC ± 10%. Isolated from the input at >500 V.
May be used to power the 4-20 mA output or other devices.
All models rated @ 40 mA max.
External Loop Power Supply: 35 VDC maximum
Digital I/O Expansion
Channels: 4 digital inputs & 4 digital outputs per module
System: Up to 2 modules for a total of 8 inputs & 8
Digital Input Logic: High: 3 to 5 VDC Low: 0 to 1.25 VDC
Digital Output Logic: High: 3.1 to 3.3 VDC Low: 0 to 0.4
Source Current: 10 mA maximum
Sink Current: 1.5 mA minimum
+5 V Terminal: To be used as pull-up for digital inputs
Relays: Four Form A (SPST) rated 3 A @ 30 VDC and 125/250
VAC resistive load; 1/14 HP (50 watts) @ 125/250 VAC
for inductive load
METEX CORPORATION LIMITED
Metex Corporation Limited has been providing superior products and services to the process control, chemical treatment, waste water, industrial and manufacturing industries for over 25 years. It is our goal to continually provide our customers with the best possible equipment, technology, and service.
Dataloggers, sensors, pumps, recorders, hand held instruments, flow instrumentation, level controls, valves, instrumentation, containers, tanks, transmitters, data loggers, digital indicators, mixers and agitators, pressure intrumentation, analyzers and controllers for a variety of industrial applications such as water quality, pH/ORP and more.
Water Analyzers and Controllers, Wireless Products, Corrosion Monitoring Equipment, Cooling Tower and Boiler Controllers, a wide variety of Pumps, Valves, Dataloggers and Recorders, HVAC, Instrumentation, Skids and Systems, Containers and Tanks from world leading manufacturers are products you will find on this site.