Loop Leader PD689 is an Intrinsically Safe and Nonincendive,
loop-powered, 1/8 DIN flow rate/totalizer designed for hazardous
process control applications. The fact that this meter is loop-powered
means that there is no need to run additional, costly power
lines into a hazardous area; the meter gets all of the power
it needs from the 4-20 mA loop. The PD689 loop-powered rate/totalizer
is built in a shallow-depth case with an FM Type 4X front and
features loop-powered backlighting and a wide -30 to 65°C
operating temperature range. It doesn't matter if it's indoors
or outdoors, in bright sunlight or a dimly lit plant, or in
an area that is wet, dirty, hot, or cold, the Loop Leader can
go just about anywhere. The PD689 can be installed in just about
any hazardous area environment under the FM, CSA, and ATEX standards.
Overall Dimensions: 4.68" x 2.45" x 3.79" (119 x 62 x 96 mm)
Weight: 5.7 oz (162 g)
Warranty: 3 years parts & labor
Input Range: 4-20 mA
Accuracy: ±0.03% of span ±1 count, square root and programmable exponent: 10-100% FS.
Calibration: Scale without signal or calibrate with signal source
Calibration Range: User programmable over entire range of meter
Minimum Span: 0.40 mA between input 1 and input 2
Note: An Error message will appear if input 1 and input 2 signals are too close together.
Input Overload: Over current protection to 2 A max.
HART Transparency: Analog input will not interfere with existing HART communications on the wired 4-20 mA signal
Decimal Point: Up to 4 places (d.dddd, dd.ddd, ddd.dd, dddd.d, or ddddd)
Function: Linear, square root, or programmable exponent
Low-Flow Cutoff: -99999 to 99999 (-99999 disables cutoff function)
Temperature Drift: 50 PPM/°C from -40 to 65°C ambient
Total Display: 0 to 99,999 main total display plus 0 to 999 total overflow for a combined 8 digit total of 99,999,999.
Alternating Display: Display may be programmed to alternate between rate and total every 10 seconds.
Time Base: Seconds, minutes, hours, or days
Totalizer Conversion Factor: 0.0001 to 99999
Totalizer: Calculates total based on rate, time base of second, minute, hour, or day, and field programmable multiplier; stored in non-volatile memory upon power loss.
Totalizer Rollover: Total rolls over when total exceed 99,999,999.
Totalizer Reset: Manual reset or automatic with time delay, or disabled for non-resettable total applications.
Open Collector Output
Rating: Isolated open collector, 30 VDC @ 175 mA max.
Alarm Output: Assign to rate or total, high or low rate alarm.
Deadband: 0-100% of full scale, user selectable
Acknowledge: ACK button resets output and screen indication.
Automatic Reset: Alarm resets automatically when signal reaches the reset point.
Pulse Output: 250 pulses/sec max; pulse width: 3 ms, fixed. If the pulse output exceeds the maximum pulse output, counts are accumulated as pending and are not lost. One pulse per total
increment, programmable from 0.0001 to 99999 (decimal point based on total selection).
* Below -20°C the LCD becomes less readable.
PD689 Approvals for Hazardous Locations
FM Approved & CSA Certified as intrinsically safe with entity for use in Class I, Div 1, Groups ABCD; Class II, Div 1, Groups EFG; Class III, Div 1; Class I, Zone 0, Group IIC; T-code = T4. Non-incendive: Suitable for use in Class I, Div 2, Groups ABCD; Class II, Div 2, Groups FG; Class III, Div 2.
Entity Parameters: Ui: 30 V; Ii: 175 mA; Ci: 0; Li: 0; Pi: 1.0 W
ATEX II 1G, Ex ia IIC T4, IP65, Ta = -40°C to 65°C
Note: Installation must be performed in accordance with Control Drawing LIM688-2
METEX CORPORATION LIMITED
Metex Corporation Limited has been providing superior products and services to the process control, chemical treatment, waste water, industrial and manufacturing industries for over 25 years. It is our goal to continually provide our customers with the best possible equipment, technology, and service.
Dataloggers, sensors, pumps, recorders, hand held instruments, flow instrumentation, level controls, valves, instrumentation, containers, tanks, transmitters, data loggers, digital indicators, mixers and agitators, pressure intrumentation, analyzers and controllers for a variety of industrial applications such as water quality, pH/ORP and more.
Water Analyzers and Controllers, Wireless Products, Corrosion Monitoring Equipment, Cooling Tower and Boiler Controllers, a wide variety of Pumps, Valves, Dataloggers and Recorders, HVAC, Instrumentation, Skids and Systems, Containers and Tanks from world leading manufacturers are products you will find on this site.